CLASSIC TABBY TESTING AND USER GUIDE

Version 3.3, 2026-11-17. For tabby-v04.15 on the M-VAVE SMK-37 Pro. The user manual and the test checklist in one, for the person who plays and tests the device. No programming needed. Sections 3 to 5 are the manual: setting up, every page of the device in the order you use it, and the workbench. Section 6 is the checklist.

This guide is for tabby-v04.15. If an older firmware is on your SMK-37, install tabby-v04.15 (section 3.2); section 2.2 lists what each release added. New in tabby-v04.15: TRANSPOSE for each clip and DELETE CLIP (section 4.11). New in tabby-v04.14: CLICK LEVEL, your own controller numbers for K1 to K4 (sections 4.11 and 4.14), a Full backup that names a song it cannot read (5.5), and the workbench no longer drops a clip's chain or length when it rewrites a song.

Where to find what: playing a song from the pads is 4.7 and 4.8. Building and changing a song on the panel is 4.9 to 4.14. Projects, sounds and housekeeping are 4.1 to 4.6 and 4.15 to 4.18. The workbench is section 5.

How to read this guide

1. WHAT CLASSIC TABBY IS TODAY

Classic Tabby is a performance MIDI sequencer firmware for the SMK-37 Pro. It started as M-VAVE's open firmware, SMK37 Open V01, and is built and changed by you on Linux.

It works like a Roland MC-707 that plays outside gear over MIDI. A song has 8 tracks. Each track has clips: short patterns of notes and controller moves, up to 64 per track, each 1 to 128 steps long. A scene is one clip for each track. The scenes of a song play in order, or you call them from the pads. Everything you launch waits for the next master cycle (one bar unless the song says otherwise), so it always lands in time. The device holds 16 songs.

You can start a song two ways. Import a MIDI file in the workbench, which is a web page in Chrome, and send it to the SMK-37 over USB. Or build it on the panel: make a clip on an empty pad, record into it or enter notes step by step, copy it, change its length, chain clips, store what plays as a scene. Both ways give the same kind of song, and you can mix them.

On stage you play it from the pads. The CLIPS page launches and stops clips on a track. The SCENES page recalls scenes. SHIFT and a pad select or mute a track. Four knobs send controllers to your gear, and a take records them.

The SMK-37 is the clock master. It sends MIDI Clock, Start, Stop and Song Position to your gear, and each note leaves within about 2 ms of its time. It can also follow a clock from USB or Bluetooth. A clip can send a program change and a bank select when its track enters it; a scene can send program changes and controller values to your synths and effects when it starts.

The SMK-37 still has its own sounds: DX7 FM (called FM6 here), BASS 303, DRUM 808, PSG and PLUCK. In a song they let you hear a part before you give it to outside gear. The keys and pads also play live.

The names in this guide are Classic Tabby's. Several differ from the words printed on the SMK-37 (the device says KNOB BANK where this guide says SHIFT, CHORD where it says ENV, PARA where it says EDIT). docs/STICKERS.md in the source has a printable sticker sheet with the Classic Tabby name for every button, knob and fader.

2. WHAT CHANGED

2.1 Changed from M-VAVE's stock Open V01

Added:

Removed:

2.2 What each Classic Tabby release changed

Oldest first. The last line is the release this guide is for.

3. SETUP

3.1 Wiring

Use this wiring for testing.

  1. USB: plug the SMK-37 Pro straight into the MacBook with its USB cable. No hub. Do not plug in the FM-1 or the AUDIO4c while you update.
  2. MIDI out to your gear, the simple way: use the TRS jack on the SMK-37 and a Type A TRS-to-DIN adapter. Plug the DIN end into the H4MIDI WC, DIN IN 1. not checked in simulator
  3. MIDI out, the better way for timing: plug the SMK-37 USB cable into the USB host port of the H4MIDI WC. The H4MIDI sends each channel to its own DIN output. One DIN cable per device. not checked in simulator
  4. The TRS jack only sends. It cannot receive MIDI. A clock from a DIN cable cannot come in through it. Clock must come in over USB or Bluetooth.
  5. Audio: take the SMK-37 audio out to your mixer or interface as usual.

Your H4MIDI settings for the Wrong Room rig are in the MIDI guide, section 14. Keep that guide next to you.

3.2 Installing from the MacBook in Chrome

Use desktop Chrome on the MacBook. Close other MIDI programs and other workbench tabs first. The SMK-37 must be plugged in, powered and idle.

Install is only needed when you want a new firmware. Install tabby-v04.15 to get everything in this guide. Take a Full backup first (Projects and sounds tab). Storage does not move.

  1. Open https://seattleuser0.github.io/classic-tabby/ in Chrome.
  2. Make a Full backup first (section 5.5). Keep the file.
  3. Click the Device update tab. Check the Version line.
  4. Click Connect device. Allow MIDI with SysEx when Chrome asks.
  5. Read the identity line. It must say SMK-37 Pro_8000001. Anything else: stop.
  6. Tick the box saying you have made a backup.
  7. Click Start update. Keep the tab open. Keep power and USB connected. It takes one to two minutes.
  8. When the page says done, the SMK-37 restarts. The boot screen shows SMK37, OFFICIAL OPEN and the version.

Never tick Force flash for a Classic Tabby update. It is only for the first move from the factory firmware.

Going back to an older build: songs saved on the device by tabby-v04.10 or later cannot be read by older firmware. Go back to an older build only with a Full backup made before tabby-v04.10: install the older build from its page in the builds list, then restore that backup. Songs made since then stay in your newer backup files; they play again when you return to the newer build and restore it.

Release candidates: a page whose address ends in -rc1, -rc2 and so on, with a red line at the top, is a build under test. Use the main page unless you were asked to try one.

(the whole of 3.1 and 3.2: the simulator has no USB) not checked in simulator

3.3 If an install stalls

An install has stalled when the progress bar stops for more than two minutes, or the page says the device stopped asking for data.

  1. Do not click Start update again in that tab. Close the tab.
  2. Switch the SMK-37 off. Wait five seconds. Switch it on. Keep the USB cable.
  3. Open the main page again, or the permanent page of the build: https://seattleuser0.github.io/classic-tabby/builds/ . The list there has one page for every build.
  4. If you open a different build's page, it tells you which build the SMK-37 is waiting for and gives you a link. Open that page.
  5. Click Connect device, then Start update. Confirm the model SMK-37 Pro when asked. The write carries on.
  6. If the SMK-37 shows nothing and does not appear as a USB MIDI device after the power cycle, stop. Do not try again. Report it.

not checked in simulator

4. USING THE DEVICE

4.1 Playing keys and pads

At start, the keys play track 1 on MIDI channel 1. The pads play track 8 on channel 10. The bottom line of HOME says KEY T1 CH01 and PAD T8 CH10.

  1. Press HOME until the overview shows eight tracks.
  2. Press a key. You hear track 1. MIDI goes out on channel 1. The lowest key is note 48 (C3).
  3. Press pad 1. You hear the 808 kick on track 8. MIDI goes out on channel 10, note 36.
  4. Press OCT+ to move the keys up one octave each press. Press OCT- to move down.
  5. Tap PAD / STEP to move the playing focus to the pads. The top shows PAD DRUM and the bottom says PAD READY - EDIT / FX. Tap PAD / STEP again to go back to the keys.
  6. Hold SHIFT. The screen lists the shortcuts. Pads 1 to 8 select a track. Pads 9 to 16 mute or unmute a track.

On the SHIFT list, the line PAD/STEP STEP EDIT is an old screen text. Step editing is on the STEP page (4.9), not there.

4.2 Choosing an FM6 (DX7) sound and its quick page

  1. On HOME, turn K5 to select the track you want.
  2. Hold SHIFT and press the button marked HOME / SRC. It is the 7th button in the right group, after ARP, PAD / STEP, SCL, ENV, MIX and BT. Do not use the HOME button in the left group: it does not open this page. The SOUND SOURCE page opens.
  3. Turn K1 until DX7 FM is lit. Or press pad 1.
  4. Press the 4th button in the left group. The page says SOUND SOURCE APPLIED.
  5. Press EDIT. The DX7 QUICK EDIT page opens. It shows the voice number out of 128 and the voice name.
  6. Turn K7 to choose the voice. Turn K6 to change the bank, A to D.
  7. Turn K1 for ALGORITHM, K2 for FEEDBACK, K3 for TRANSPOSE and K4 for LEVEL.
  8. Press EDIT again to go back. A star near the top means the track has unsaved changes.

On any other sound, pressing EDIT only says VOICE EDIT MOVED TO WORKBENCH. Other sounds are edited in the workbench.

4.3 Track roles: PROJECT, LIVE, OFF

  1. Hold SHIFT and press HOME / SRC (the 7th button in the right group). The SOUND SOURCE page opens for the selected track.
  2. Turn K2 right. TRACK goes PROJECT, then LIVE, then OFF. Turn K2 left to go back.
  3. The screen explains each choice under the line. Press HOME to leave.

4.4 MIDI channels and output per track

Each track has its own input channel, output channel, local or MIDI choice and port.

  1. Hold SHIFT and press SEQ. The MIDI TRACK page opens.
  2. Turn K5 to choose the track. The top line shows T1 to T8.
  3. K1 IN CH is the channel the track listens to from USB or Bluetooth.
  4. K2 OUT CH is the channel the track sends on. When it changes, the screen says MIDI SETTING - NOTES RELEASED.
  5. K3 SEQ: LOCAL plays the built-in sound only. BOTH plays the built-in sound and sends MIDI. MIDI sends MIDI only.
  6. K4 OUT PORT: ALL sends on USB, Bluetooth and the TRS jack. OFF sends nothing from this track. Turn K4 left for OFF.
  7. Press HOME to leave.

The port setting is the same for all tracks. A song's own output channel for a track wins while the song plays. When the song stops, the device setting is back.

4.5 The SYNC / MIDI page: clock source, tempo, swing

  1. Press SEQ on any page. The SYNC / MIDI page opens.
  2. K1 CLOCK: INT uses the SMK-37's own clock. MIDI waits for an outside clock. Turn K1 right for MIDI, left for INT.
  3. K2 CLK IN: AUTO, USB, BLE or DIN. Choose USB or BLE for a clock from outside. Do not choose DIN: the TRS jack receives nothing.
  4. K3 SWING: 0 to 50 percent. It is saved in the project.
  5. K4 SEQ OUT: OFF sends no notes and no clock. ON sends notes and clock. CLOCK sends clock and Start and Stop only.
  6. K7 KEY OUT: ON or OFF. It switches the MIDI out of the keys and pads.
  7. The tempo is not on this page. It says BPM: SET ON HOME K4.

With CLOCK on MIDI, the screen says WAIT MIDI CLOCK until a clock arrives. Songs cannot start then. Keep CLOCK on INT for songs.

Tempo: on HOME turn K4. Or tap the tempo: hold HOME and tap SEQ. The first tap says TAP AGAIN / HOME+SEQ.

4.6 The ACTIONS menu

  1. Press SEQ and EDIT together. The ACTIONS menu opens.
  2. Do not hold SEQ alone. It does not open ACTIONS. The SYNC / MIDI page of tabby-v04.2 says SEQ+EDIT: ACTIONS (older firmware said HOLD SEQ: ACTIONS, which was wrong).
  3. The first line shows the storage: USER 471040 SONG READY. FREE and RECLAIM show at the bottom.
  4. Turn K1 or K5 to choose an entry. Press the 4th button in the left group to run it. HOME leaves.
  5. The entries are: COPY TIMBRE, PASTE TIMBRE, STOP ALL / REWIND, ERASE OLD DATA, SONG MODE, COMPACT SONG STORAGE, SEND SETUP and A2 FAST MIDI: ON (or OFF). The last one switches fast MIDI for this session only.
  6. STOP ALL / REWIND stops all sound and rewinds. It is in the list; on its own it shows DONE.

4.7 Song mode: choose a song, play, recall a scene

You need a song on the device first (section 5.3).

  1. Press SEQ and EDIT together to open ACTIONS.
  2. Turn K5 until SONG MODE is lit. Press the 4th button in the left group. The SONG page opens.
  3. Turn K5 or K7 to choose song 1 to 16. An empty slot says NO SONG HERE - UPLOAD FROM THE WEB WORKBENCH.
  4. Make sure the project you want is loaded. The song uses whatever project is loaded. It does not load one for you.
  5. Press PLAY. The page says PLAYING. SCENE, X (the pass of the repeat) and BAR show where it is. NEXT shows what follows. Press PLAY again to stop. A scene is one row of the song: one clip for each track.
  6. To recall a scene: press a pad. The pad number is the scene on the pad page. The page shows TO SCENE n in amber and the pad blinks green. The scene starts on the next bar. Then the page shows the new SCENE and its pad is green.
  7. K4 switches JUMP: NEXT CYCLE and JUMP: SCENE END. not checked in simulator
  8. OCT+ and OCT- move the pad page by 16 scenes. not checked in simulator
  9. A pad with no scene, or a press while the song is stopped, says NO SUCH SCENE / NOT PLAYING.
  10. Press HOME to leave the page. The song keeps playing.

With CLOCK on MIDI (tabby-v04.3.1 and later) PLAY arms the song and the master runs it: Start, Continue, Stop and Song Position Pointer, over USB or Bluetooth. See test T32. not checked in simulator

4.8 Clip launching (tabby-v04.7)

Clip launching lets one track loop one of its clips while the others follow the song. A clip is one pattern of one track. Each track has its own clips, numbered from 1. The pads show 16 of them at a time.

  1. Press BT. The CLIPS page opens, from any page. BT again goes back where you were. (On the SONG page SCL opens it too.)
  2. Hold SHIFT and press a pad from 1 to 8 to choose a track, or turn K5. The screen says TRACK SELECTED.
  3. Look at the pads. Off: no clip. Dim white: a clip. Green: the clip that plays.
  4. Press PLAY if the song is not running. (Or press a pad first: it blinks, the screen says RESERVED - PLAY STARTS IT, and PLAY starts the song with that clip on the track.) Then press a white pad. It blinks green and the screen says LAUNCH AT NEXT CYCLE. On the next bar line the clip starts and the pad is green. The column for the track shows CLIP.
  5. To stop the track: press the green pad. It blinks red and the screen says STOP AT NEXT CYCLE. On the next bar line the track is silent. The column shows STOP.
  6. Changed your mind? Press the blinking pad again before the bar line. The screen says TAKEN BACK.
  7. To look at a clip without launching it: hold its pad for half a second. The screen says SELECTED ONLY - TAKEN BACK. The pad is bright white, and the SELECTED line shows its length.
  8. To bring the track back to the song: press ENV. The screen says TRACK TO SCENES AT CYCLE. The column shows >SCN, then SCENE. SHIFT and ENV together bring every track back.
  9. To mute a track: hold SHIFT and press pad 9 to 16 for track 1 to 8. The track's pads turn orange and the screen says MUTED ALL. Its notes stop on MIDI out too, and the clip keeps running, so unmuting brings it back in time. Blue pads and MUTED INT mean the other mute: the one from the MIX page, which silences only the SMK-37's own sound of the track and lets its MIDI notes go out.
  10. OCT+ and OCT- (or K6) show the next 16 clips. The page then shows PADS 17 - 32.
  11. Press SCL for the SONG page, where the pads recall scenes. Press PLAY to stop the song.

"The next cycle" is the next bar line. A song imported from a 3/4 file uses 3/4 bars. The complete list of what every control does on these pages is in docs/CONTROL-MAP.md.

A jump on the SONG page cancels every launch and brings all tracks back to the song.

4.9 Editing a clip: the STEP page (tabby-v04.8)

Here you change the notes of a clip on the SMK-37 itself. The pads say where, the keys say what.

  1. On the CLIPS page select a clip: hold its pad for half a second (it turns bright white), or launch it. Press EDIT. The STEP page opens: STEP, the track, CLIP and its number, SAVED.
  2. The 16 pads are the 16 steps of one bar. Green pads hold notes. OCT+ and OCT- show the next and the previous bar.
  3. Press a pad. It turns cyan and the screen lists the notes on that step.
  4. Play a key. Its note is entered on the step, as loud as you played it, one step long. The screen says NOTE ENTERED and UNSAVED. Play the same key again to remove it. Play more keys for a chord.
  5. Turn K2 for the velocity, K3 to move the note a little early or late, K4 for its length. With several notes on the step, K1 chooses which one (the > mark).
  6. Press the pad again to let go of the step. Now a key only sets the NOTE shown on the screen.
  7. For drums: press SCL. The screen says PADS TOGGLE and the note. Now each pad press puts that note on its step or takes it off. Amber pads hold that note. SCL again goes back.
  8. ENV clears the selected step. FX undoes the last change, up to four. SHIFT and FX redo.
  9. To hear it: press PLAY. The song plays your change even though it is not saved. If the clip is launched and looping (go back with EDIT, press its pad, come back with EDIT), each change is heard from the clip's next loop, and a white pad runs along with the music.
  10. To save: stop the song. Press the 4th button in the left group: CLIP SAVED. If you forget, the clip is saved by itself ten seconds after the song stopped. While the song plays the button says STOP TO SAVE.
  11. To throw the changes away: SHIFT and ENV. The screen says EDITS DISCARDED.
  12. EDIT goes back to the CLIPS page.

Only one clip can be unsaved at a time. Unsaved changes are lost when you switch the SMK-37 off. Take a Full backup of a song before you edit it on the device if you want the old version back later.

4.10 Recording into a clip (tabby-v04.9)

REC records what you play into a clip while the clip loops. What is already in the clip stays; you add to it.

  1. On the CLIPS page choose the track (SHIFT and pad 1 to 8) and select the clip: hold its pad for half a second.
  2. Press REC. If the song is stopped the screen says REC ARMED - PLAY STARTS IT: press PLAY. If the song is playing, the clip starts looping at the next bar line and the screen says RECORDING. The REC lamp is lit.
  3. Play. Each note appears in the clip when you let the key go, and you hear it from the clip's next time round.
  4. Notes land on the nearest step (input quantize). To keep your own timing, hold SHIFT and press REC: INPUT QUANTIZE OFF. Do it again to switch it back on.
  5. Outside gear can record too: send notes to the SMK-37 over USB on the track's channel. Mod wheel, pitch bend and other controllers are recorded as well; a long sweep is thinned so it does not fill the clip.
  6. Press REC again: REC STOPPED. The clip is UNSAVED. It is saved like a step edit: stop the song, and press the 4th button in the left group or wait ten seconds.
  7. Not happy with the take? Press EDIT for the STEP page and press FX: the whole take is gone. SHIFT and FX bring it back.

A clip holds 512 events. If it fills up, recording stops by itself and the screen says CLIP FULL - 512 EVENTS - REC STOPPED. Nothing you recorded is lost.

4.11 New clips, CLIP SETTING, click and count-in, storing a scene (tabby-v04.10)

A new clip

  1. On CLIPS press an empty pad. It lights dim cyan and the screen says EMPTY PAD - REC OR EDIT MAKES A CLIP.
  2. Press REC to record into a new clip there (4.10), or EDIT to enter notes on the STEP page (4.9). The new clip is one bar long (one master cycle).
  3. The CLIPS page shows UNSAVED. Stop the song and press the 4th button in the left group, or wait ten seconds: SAVED. The new clip is now part of the song.

CLIP SETTING

  1. On CLIPS select a clip (hold its pad) and press FX. The SETTING page has two pages. Page 1/2 is the clip: LENGTH, NEXT CLIP, AFTER, TIMES, PROGRAM, BANK MSB, BANK LSB, COPY TO PAD, TRANSPOSE and DELETE CLIP. Page 2/2 is the song: COUNT-IN, CLICK, CLICK OUT, CLICK CHANNEL, CLICK NOTE, CLICK LEVEL and K1 CONTROLLER to K4 CONTROLLER. K5 walks through all the lines; the page changes by itself.
  2. Turn K5 to choose a line. Turn K1 to change it; K2 changes it by 16.
  3. LENGTH is the clip's length, 1 to 128 steps. Making it shorter removes the notes past the new end; FX on the STEP page brings them back.
  4. COPY TO PAD: turn K1 to an empty pad and press the 4th button in the left group. The copy is open and UNSAVED. A clip you changed must be saved before you copy it.
  5. TRANSPOSE (tabby-v04.15): K1 moves the clip's notes up or down, 12 semitones at most. The clip itself is not changed: 0 plays it as it was. You hear it from the clip's next loop.
  6. DELETE CLIP (tabby-v04.15): stop the song, turn K5 to DELETE CLIP and press the 4th button in the left group. The screen says PRESS AGAIN TO DELETE THE CLIP. Press it again within two seconds: CLIP DELETED - SAVE THE SONG. A clip that a scene uses is not deleted; the screen names the scene.
  7. FX goes back to CLIPS.

Every clip loops at its own length: a 1-bar clip in a 4-bar scene plays four times. Songs you imported play as before.

Click and count-in

  1. On the SETTING page turn K5 to CLICK. K1 chooses OFF, WHEN RECORDING or ALWAYS.
  2. CLICK OUT: INTERNAL is a click on the SMK-37's audio output. MIDI NOTE sends a note on CLICK CHANNEL and CLICK NOTE (channel 10, note 37 unless you change them). BOTH does both. If your audio goes to the house mix, use MIDI NOTE.
  3. COUNT-IN: OFF, 1, 2 or 4 CYCLES. Arm a take with REC while the song is stopped, then press PLAY: the click counts in, the screen shows COUNT-IN and the beats left, then the song starts.
  4. CLICK LEVEL (tabby-v04.14): LOW, MID or HIGH for the internal click. Each step is twice as loud. A song you never set is on MID; HIGH is about as loud as a note.
  5. These settings belong to the song and are saved with it. A song you never set has no click.

Storing a scene

  1. Let the song play. Launch the clips you want on their tracks.
  2. Go to SCENES (SCL). Hold an empty pad for half a second. The screen says STORED AS A NEW SCENE. The new scene is added after the last one.
  3. Press its pad to recall it later. It repeats until you recall another scene.
  4. A pad that already holds a scene is never written over. Save the song when stopped (4th button in the left group).

4.12 Clip chains (tabby-v04.11)

  1. On CLIPS select a clip and press FX. After LENGTH the SETTING page has NEXT CLIP, AFTER and TIMES.
  2. NEXT CLIP: turn K1. STAY means no chain. STOP stops the track. CLIP n goes on with that clip of the same track; K1 only stops at pads that hold a clip.
  3. AFTER: CLIP END, or a number of steps (K2 changes it by 16). TIMES: how many times before the chain is due.
  4. Save (stop, 4th button in the left group). Launch the clip from its pad. Under the track's column the CLIPS page shows +05 (clip 5 is next) or +STP.
  5. The chain only runs on a track you launched by hand. A track that follows the scenes ignores it. A pad press, ENV or a scene recall ends it.

4.13 The scene chain (tabby-v04.12)

  1. Open SCENES (SCL from CLIPS). The line LEN shows the length of the scene that plays, in master cycles, then THEN and CHAIN.
  2. K1 changes how many times the scene plays before the next one. K2 chooses THEN NEXT (the next scene follows by itself) or THEN STAY (it repeats until you recall another).
  3. K3 right: CHAIN HELD. The scene that plays repeats until you turn K3 left again (CHAIN RUNS) or press a scene pad.
  4. While the song is stopped, press a scene pad: RESERVED - PLAY STARTS AT THIS SCENE. PLAY starts there. The knobs then work on that scene.
  5. A pad always wins: the song jumps to its scene and goes on from there. Save the song when stopped.

4.14 A clip's program and bank; the controller knobs (tabby-v04.13)

  1. On CLIPS select a clip and press FX. After TIMES the page has PROGRAM, BANK MSB and BANK LSB.
  2. PROGRAM: OFF or 1 to 128. BANK MSB: OFF or 0 to 127; BANK LSB works once BANK MSB has a value. Save.
  3. When the track enters the clip (its pad, a chain, a scene), the bank select and the program change go out on the track's channel, just before the clip's first notes. They go to MIDI out only.
  4. On the CLIPS page turn K1 to K4: they send controllers 74, 71, 1 and 11 for the selected track. The screen shows the value.
  5. Press REC and turn a knob: the movement is recorded into the clip and plays back in the loop.
  6. To send other controllers (tabby-v04.14): press FX, turn K5 to K1 CONTROLLER (page 2/2) and choose a number from 0 to 127 with K1 (K2 moves by 16). The same for K2, K3 and K4 CONTROLLER. Save. The numbers belong to the song.

4.15 Saving a project, and the STOP TO SAVE rule

Your sounds, mixer and MIDI settings live in a project. There are 16 project slots.

  1. Press the 4th button in the left group. The SAVE PROJECT page opens. It shows USER 01/16 and a working name.
  2. Turn K5 or K7 to choose the slot. K1 moves the cursor in the name and K2 changes the letter.
  3. Press the 4th button again. The screen says PROJECT SAVED and goes back to the overview.
  4. HOME cancels without saving.

STOP TO SAVE: while a song or pattern plays, the device writes nothing to flash. If you press the 4th button a second time while something plays, the page says STOP TO SAVE in orange. Stop the song, then save. Changes you made while playing are kept and can be saved after the stop.

The same rule holds for ERASE and COMPACT in ACTIONS and for any write from the workbench.

4.16 Loading a project

  1. On the overview, press HOME. The PRESETS list opens.
  2. Turn K5 or K7 to pick a project, or press a pad from 1 to 16 to load it directly.
  3. Press PLAY to load and run. An empty slot says EMPTY SLOT - CHOOSE ANOTHER.
  4. HOME goes back. HOME with the 4th button undoes the last change.

4.17 Erasing old data

After a storage move, the device can announce OLD DATA IN SONG STORAGE - SEE ACTIONS for six seconds. Then the SONG page cannot write or play songs. The ACTIONS first line says SONG OLD DATA.

  1. Press SEQ and EDIT together. Turn K1 or K5 to ERASE OLD DATA.
  2. Press the 4th button in the left group. The screen says ERASE OLD DATA? and, at the bottom, 4TH LEFT BTN CONFIRM and HOME CANCEL.
  3. Press the 4th button again. The page says DONE and the first line changes to SONG READY.
  4. Nothing is erased without the second press. Projects, tunings and settings are never touched.

4.18 Other useful controls

5. USING THE WORKBENCH

Open https://seattleuser0.github.io/classic-tabby/ in desktop Chrome. The tabs are Play & edit, Projects & sounds, Device update and Help. Help has 22 chapters. Chapter 00 says what changed in tabby-v04.

The Play & edit tab is a simulator of the device. It runs the same firmware code in the browser. Use it to try things safely.

5.1 Connecting

  1. Plug in the SMK-37 and close other MIDI programs.
  2. Open the Projects & sounds tab.
  3. Click Connect project library. Allow MIDI with SysEx when Chrome asks.
  4. The page reads what the device can do. The Song mode group and the Bluetooth settings group become usable.

not checked in simulator

5.2 Importing a MIDI file into a song

  1. In Projects & sounds, open Import MIDI file (Classic Tabby).
  2. Choose the .mid file. The summary shows format, tempo, tracks and bars. Warnings show under it.
  3. Assign each part to a track from 1 to 8, or skip it. Set OUT CH per track to the channel of the gear that should play it.
  4. Check the options. Quantize is off by default, which keeps the timing exact. Bars per row offers lengths that stay on bar lines.
  5. Check the resulting song and the list called Dropped or changed.
  6. Choose the Song slot. Click Write song and confirm. The panel shows the plan and the time taken.
  7. If the slot already has a song, the page deletes it first and says so. Click Export .tabby first if you want to keep it.
  8. Scenes (tabby-v04.6): with the box "write the song as scenes and clips" ticked (it is ticked at the start) the song is stored as scenes with clips of up to 8 bars and the master cycle set to one bar of the file. Untick it to write rows, which older firmware can play.
  9. Chords of more than four notes, controller events and long rows (tabby-v04.5): the importer keeps every note of a chord. With the box "keep controller, pitch bend and aftertouch events in the clips" ticked (it is ticked at the start) it also keeps the mod wheel, sustain pedal, pitch bend and aftertouch of each part, thinned to one value per 1/8 step. Bars per row offers up to 128 steps. A part that needs any of this is stored as a "v3 clip"; the summary says how many. The step editor in Song mode cannot show a v3 clip, but it keeps it when you write or export the song. A song with v3 clips or long rows needs tabby-v04.5 on the SMK-37; the page refuses to write it to older firmware and says why.

The target is chosen in the Song mode group: Device (project library) or Browser simulator. The simulator is safe to try first.

5.3 Writing a song to the device

  1. Connect the project library (5.1). Stop anything playing on the device.
  2. Open Song mode (Classic Tabby). Set Target to Device.
  3. Choose the Song slot. Click Read song to see what is there.
  4. Click Write song. The page writes the record, then every block, then reads it back and compares. Audio pauses a little at the end of each batch. Write songs before a set, not during one.
  5. On the device, open SONG MODE (4.7) and play it.
  6. Storage status tells you how much room is left. After many rewrites, run COMPACT SONG STORAGE in ACTIONS to reclaim old blocks.

(writing to a real device). Writing to the Browser simulator target is the same path. not checked in simulator

5.4 Rig profiles and row events

The rig tells the workbench which device is on each MIDI channel. Then the row event editor shows preset names instead of numbers.

  1. Open Rig setup (Classic Tabby). The built-in Wrong Room profile is read-only. Click Copy to my rig to get one you can change.
  2. Each line is one MIDI channel: Device, Name, Gap ms, Lead ms, Numbering and Names. Gap ms is the pause a device needs after a program change. Lead ms sends the program change that long before the bar.
  3. Export rig (.json) and Import rig save and load your rig. It is kept in this browser.
  4. In Song mode, under the row table, choose a Row. Use Add on channel and the type: Program, Control change or Gap in ms.
  5. A row holds up to 32 events. A song holds up to 292. Row 1 is marked SEND SETUP.
  6. Events go to outside gear only. They do not change the SMK-37's own sounds.
  7. On the device, SEND SETUP in ACTIONS sends row 1's events at once. With the song stopped and loaded, the notice says SETUP SENT - ROW 1 EVENTS. With the song playing it says STOP THE SONG FIRST. With no song loaded it says NO SONG LOADED. not checked in simulator

5.5 Full backup and restore

Make a Full backup before every firmware update.

  1. In Projects & sounds, open Full backup and restore (Classic Tabby). Stop any song first.
  2. Click Full backup. A file is saved on the computer. It holds the 16 project slots, device settings, every song, and your My rig profile. It does not hold Bluetooth pairings.
  3. To restore: choose the Backup file, click Full restore, and confirm. It checks the whole file before it writes anything.
  4. At the end it reads everything back. It shows PASS or the first difference. Click Verify against file any time to check again.
  5. If the page cannot read a song, the backup stops and says so: STOPPED at song 7: this page cannot read it. No file was made and nothing on the device changed. This happens when the song was saved by newer firmware than the page you opened. Open the page of the firmware that is on the device (the builds list has every page) and make the backup there.

A factory restore overwrites the last 40 KB of song storage. Export your songs as .tabby files first.

not checked in simulator

5.6 The Diagnostics panel

  1. In Projects & sounds, open Diagnostics (timing counters and control-loop profile).
  2. Click Reset counters. Play a song for the time you want to measure.
  3. Click Read counters. Click Copy as text to paste the numbers into a message.
  4. The counters show the control loop period, the longest flash erase and write, the time from a key press to MIDI, and busy time and lost ticks.
  5. One line starts with "flash part". It names the flash chip inside the SMK-37: its JEDEC ID, like 0xEB6014, and its size, 1024 KiB. The device read them when it started. The line is a report for problem reports. The device works the same with any chip, and nothing checks this line. The simulator shows "flash part: none (simulator)".

not checked in simulator

5.7 Bluetooth settings

In Projects & sounds, the Bluetooth settings group has Bluetooth on, Bluetooth audio, the BLE MIDI role (DEVICE or HOST) and Forget MIDI pairs. Each change is written at once. Cables are better than Bluetooth for notes and clock.

not checked in simulator

6. TEST CHECKLIST

Mark each test PASS or FAIL. Write what you saw. Run a test only when its set-up is ready. The tests are grouped by area.

Tests with real gear are in group G.

GROUP A. START UP

T1. Boot screen and version

Set up: SMK-37 Pro on USB power, nothing else.

  1. Switch on. not checked in simulator
  2. Watch the boot screen.

You should see: SMK37, OFFICIAL OPEN and the version line. Then the HOME overview.

Result: PASS / FAIL   Notes:

T2. HOME overview

Set up: T1 done.

  1. Look at the overview.

You should see: 8 tracks listed, BPM 120 or your project's tempo, and at the bottom KEY T1 CH01 PAD T8 CH10.

Result: PASS / FAIL   Notes:

T3. Storage state

Set up: T2 done.

  1. Press SEQ and EDIT together.

You should see: ACTIONS with the first line USER 471040 SONG READY. FREE and RECLAIM at the bottom. Press HOME to leave.

Result: PASS / FAIL   Notes:

GROUP B. PLAYING

T4. Keys

Set up: HOME overview.

  1. Press the lowest key, then a key in the middle.

You should hear: track 1's sound. The outside MIDI shows channel 1, lowest key note 48. (Check the MIDI note on a monitor if you have one.) (the monitor) not checked in simulator

Result: PASS / FAIL   Notes:

T5. Pads

Set up: HOME overview.

  1. Press pad 1, then pad 2.

You should hear: the 808 drum sounds on track 8. MIDI goes out on channel 10, pad 1 is note 36.

Result: PASS / FAIL   Notes:

T6. Octave buttons

Set up: HOME overview.

  1. Press OCT+ twice. Press a key.
  2. Press OCT- four times. Press the same key.

You should hear: two octaves higher, then two octaves lower than the start. MIDI notes: start 60, then 84, then 36 for the same key.

Result: PASS / FAIL   Notes:

T7. Keys and pads focus

Set up: HOME overview.

  1. Tap PAD / STEP.
  2. Press pad 1.
  3. Tap PAD / STEP again.

You should see: PAD DRUM at the top and PAD READY - EDIT / FX at the bottom after step 1. Pad 1 still plays the kick. After step 3 the top shows KEY PLAY again.

Result: PASS / FAIL   Notes:

T8. Mute with SHIFT and a pad

Set up: HOME overview.

  1. Hold SHIFT. Press pad 9. Release SHIFT.
  2. Hold SHIFT. Press pad 9 again.

You should see: track 1 shows M-ALL, then the mute goes away. The screen says TRACK MUTED: SOUND AND MIDI, then TRACK UNMUTED. The overview shows M-ALL for this mute and M-INT for a mute set on the MIX page.

Result: PASS / FAIL   Notes:

T9. Mixer

Set up: HOME overview.

  1. Tap MIX.
  2. Press pad 1.
  3. Tap MIX again.

You should see: the mixer with MUTE and SOLO cells. Pad 1 mutes track 1. The overview comes back after step 3.

Result: PASS / FAIL   Notes:

GROUP C. SOUNDS AND TRACKS

T10. Choose the FM6 sound

Set up: HOME overview.

  1. Turn K5 to select track 3 (PSG).
  2. Hold SHIFT, press HOME / SRC (the 7th button in the right group). Turn K1 left to DX7 FM. Press the 4th button in the left group.

You should see: SOUND SOURCE page with DX7 FM lit, then SOUND SOURCE APPLIED on the overview. Track 3 now says DX7 FM. To hear it, select track 3 and play the keys.

Result: PASS / FAIL   Notes:

T11. FM6 quick page

Set up: T10 done, track 3 selected.

  1. Press EDIT.
  2. Turn K7 three clicks. Turn K6 one click. Turn K1 two clicks.
  3. Press EDIT.

You should see: DX7 QUICK EDIT. The voice number changes with K7. The bank changes with K6. ALGORITHM changes with K1. A star shows at the top. Back on the overview, the track shows EDITED.

Result: PASS / FAIL   Notes:

T12. Other sounds say "moved to workbench"

Set up: HOME overview, track 2 (BASS 303) selected.

  1. Press EDIT.

You should see: VOICE EDIT MOVED TO WORKBENCH.

Result: PASS / FAIL   Notes:

T13. Track roles

Set up: HOME overview.

  1. Hold SHIFT, press HOME / SRC. Turn K2 right once, then once more.

You should see: PROJECT, then LIVE with KEEP SOUND ON PROJECT LOAD, then OFF with TURN K2 LEFT TO ENABLE. Turn K2 left twice to get back to PROJECT.

Result: PASS / FAIL   Notes:

T14. Input and output channels per track

Set up: HOME overview.

  1. Hold SHIFT, press SEQ. Turn K5 to track 4.
  2. Turn K2 three clicks.
  3. Turn K1 two clicks.

You should see: the MIDI TRACK page. OUT CH changes by three. IN CH changes by two. The screen says MIDI SETTING - NOTES RELEASED after a change. A key played on track 4 now goes out on the new channel. (the outside gear) not checked in simulator

Result: PASS / FAIL   Notes:

T15. LOCAL, BOTH, MIDI

Set up: T14 done. Track 4 on the MIDI TRACK page.

  1. Turn K3 right once.

You should see: SEQ changes from BOTH to MIDI. The screen says SEQ OUTPUT UPDATED. The track makes no sound inside any more but still sends MIDI.

Result: PASS / FAIL   Notes:

T16. Output port off

Set up: MIDI TRACK page.

  1. Turn K4 left once.

You should see: OUT PORT shows OFF. Nothing is sent from this track.

Result: PASS / FAIL   Notes:

GROUP D. SYNC / MIDI PAGE AND TEMPO

T17. The SYNC / MIDI page

Set up: HOME overview.

  1. Press SEQ.

You should see: SYNC / MIDI with CLOCK, CLK IN, SWING, SEQ OUT, KEY OUT and the line BPM: 120 SET ON HOME K4.

Result: PASS / FAIL   Notes:

T18. Clock source

Set up: T17 done.

  1. Turn K1 right once.
  2. Turn K2 right once.
  3. Turn K1 left once.

You should see: CLOCK MIDI and BPM WAIT after step 1. CLK IN USB after step 2. CLOCK INT after step 3 and the tempo back.

Result: PASS / FAIL   Notes:

T19. Swing and SEQ OUT

Set up: SYNC / MIDI page.

  1. Turn K3 five clicks right.
  2. Turn K4 right once.

You should see: SWING 5%. SEQ OUT CLOCK. Set SEQ OUT back to ON.

Result: PASS / FAIL   Notes:

T20. Tempo

Set up: HOME overview.

  1. Turn K4 five clicks right.
  2. Hold HOME and tap SEQ twice.

You should see: BPM goes up by five. The first tap says TAP AGAIN / HOME+SEQ. The second tap sets a tempo from your tapping.

Result: PASS / FAIL   Notes:

GROUP E. ACTIONS, PROJECTS AND SAVING

T21. The ACTIONS menu

Set up: HOME overview.

  1. Press SEQ and EDIT together.
  2. Turn K5 right until you have seen all seven entries.

You should see: COPY TIMBRE, PASTE TIMBRE, STOP ALL / REWIND, ERASE OLD DATA, SONG MODE, COMPACT SONG STORAGE, SEND SETUP, A2 FAST MIDI: ON. The bottom line says K1/K5 ACTION 4TH LEFT BTN DOES IT.

Result: PASS / FAIL   Notes:

T22. Holding SEQ alone

Set up: HOME overview.

  1. Hold SEQ alone for two seconds.

You should see: SYNC / MIDI opens, not ACTIONS. This is expected. Older firmware showed the wrong text HOLD SEQ: ACTIONS; tabby-v04.2 shows SEQ+EDIT: ACTIONS.

Result: PASS / FAIL   Notes:

T23. Save a project

Set up: HOME overview. Nothing playing.

  1. Press the 4th button in the left group.
  2. Turn K7 two clicks.
  3. Press the 4th button again.

You should see: SAVE PROJECT with USER 01/16 and a name. Slot 03 after step 2. PROJECT SAVED after step 3.

Result: PASS / FAIL   Notes:

T24. STOP TO SAVE

Set up: a song loaded and playing (T29).

  1. Press the 4th button. Press it again.

You should see: SAVE PROJECT, then STOP TO SAVE in orange. Nothing is written. Stop the song and save again: PROJECT SAVED.

Result: PASS / FAIL   Notes:

T25. Load a project

Set up: T23 done. HOME overview.

  1. Press HOME. Press pad 3.

You should see: the PRESETS list, then your saved project loaded.

Result: PASS / FAIL   Notes:

T26. Erase old data

Set up: only if the device says OLD DATA IN SONG STORAGE. If it does not, write "not needed".

  1. Press SEQ and EDIT together. Turn K1 or K5 to ERASE OLD DATA. Press the 4th button.
  2. Check the screen. Press the 4th button again.

You should see: ERASE OLD DATA? and 4TH LEFT BTN CONFIRM. After the second press, DONE and SONG READY.

Result: PASS / FAIL   Notes:

GROUP F. SONGS

T27. Import a MIDI file and write it to the browser simulator

Set up: Chrome, the workbench, and any .mid file of your own.

  1. Projects & sounds, Song mode, Target: Browser simulator.
  2. Import MIDI file. Assign parts. Write song to slot 1.
  3. On the Play & edit tab, press the Song mode shortcut.

You should see: the plan and a read-back check with no difference. Then the SONG page with the song name. (the import screens; the SONG page itself was checked) not checked in simulator

Result: PASS / FAIL   Notes:

T28. Write the song to the device

Set up: device connected (5.1), nothing playing.

  1. Target: Device. Write song to slot 1.

You should see: the page writes the record and the blocks, then reads back and says it matches. A short audio pause is normal.

Result: PASS / FAIL   Notes:

T29. Choose a song and play it

Set up: T28 done. Device on HOME. CLOCK on INT.

  1. Press SEQ and EDIT together. Turn K5 to SONG MODE. Press the 4th button.
  2. Turn K5 right to song 2, then left to song 1.
  3. Press PLAY.

You should see: SONG 01 and the name. Song 2 empty says NO SONG HERE - UPLOAD FROM THE WEB WORKBENCH. After PLAY: PLAYING, SCENE, X, BAR and NEXT change as it goes.

Result: PASS / FAIL   Notes:

T30. Recall a scene

Set up: T29 playing, a song with at least 3 scenes (rows).

  1. Press pad 3.

You should see: TO SCENE 003 in amber and pad 3 blinking green, then SCENE 003 on the next bar with pad 3 green. All tracks change together.

Result: PASS / FAIL   Notes:

T31. Stop the song

Set up: T29 playing.

  1. Press PLAY.

You should see: the page says STOPPED - PLAY STARTS. Every note is released. MIDI Stop is sent once.

Result: PASS / FAIL   Notes:

T32. Song follows an external clock (tabby-v04.3.1)

Set up: a DAW or MIDI app on the MacBook sends MIDI clock, Start, Stop and Continue to the SMK-37 over USB. SYNC / MIDI with CLOCK on MIDI (K1). Song selected on the SONG page.

  1. Press PLAY on the SONG page. The page says ARMED: START?
  2. Press play in the DAW. At its first clock pulse the song starts and the page says FOLLOWING. The notes stay with the DAW's beat.
  3. Change the DAW's tempo. The song keeps up.
  4. Press stop in the DAW. The page says STOP BY MASTER and every note is released. Press continue: it goes on from where it stopped.
  5. Pause the clock for one second (or unplug USB for one second and plug it back). The page says HOLD: NO CLOCK and the notes stop; when the clock returns, it carries on from the same place.
  6. Pause the clock for five seconds. The page says LOST - CONTINUE. When the clock returns, the song stays silent until you press continue or start.

You should see and hear: the song following the DAW as described. not checked in simulator

Result: PASS / FAIL   Notes:

T33. Launch a clip on one track

Set up: T29 playing, a song where track 1 has at least two clips (the pads on the CLIPS page show two white or green pads).

  1. Press BT. Hold SHIFT and press pad 1. Release SHIFT.
  2. Press a white pad.
  3. Wait for the next bar.

You should see: CLIPS T1, TRACK SELECTED, then LAUNCH AT NEXT CYCLE and the pad blinking green. After the bar line the pad is green and the column says CLIP. The other tracks go on with the song.

Result: PASS / FAIL   Notes:

T34. Stop and bring a track back

Set up: T33 done.

  1. Press the green pad.
  2. Wait a bar. Press ENV.
  3. Wait a bar.

You should see: STOP AT NEXT CYCLE, the pad blinking red and >STP, then STOP. TRACK TO SCENES AT CYCLE and >SCN, then SCENE.

Result: PASS / FAIL   Notes:

T35. A jump cancels launches

Set up: T33 done, track 1 launched.

  1. Press SCL to go to the SONG page. Press a pad.

You should see: after the landing, every track follows the song again. not checked in simulator

Result: PASS / FAIL   Notes:

T36. Compact the storage

Set up: song storage with some old blocks (Storage status shows RECLAIM above zero), nothing playing.

  1. Press SEQ and EDIT together. Turn K5 to COMPACT SONG STORAGE. Press the 4th button. Press it again.

You should see: COMPACT SONG STORAGE? and then COMPACTING STORAGE... for a few seconds. RECLAIM goes to 0. not checked in simulator

Result: PASS / FAIL   Notes:

GROUP G. WORKBENCH

T37. Connect the project library

Set up: device on USB, close other MIDI programs.

  1. Projects & sounds, Connect project library.

You should see: the page connects, reads the capabilities and shows the Song mode and Bluetooth settings groups. not checked in simulator

Result: PASS / FAIL   Notes:

T38. Full backup

Set up: T37 done. Nothing playing.

  1. Full backup.

You should see: a backup file saved on the computer. Keep it. not checked in simulator

Result: PASS / FAIL   Notes:

T39. Full restore and verify

Set up: T38 done. Nothing playing.

  1. Choose the file. Full restore. Confirm.
  2. Click Verify against file.

You should see: PASS at the end of the restore and after Verify. not checked in simulator

Result: PASS / FAIL   Notes:

T40. Rig copy

Set up: workbench Rig setup.

  1. Click Copy to my rig. Change the Name of channel 5.
  2. Reload the page.

You should see: your copy with the changed name is still there. not checked in simulator

Result: PASS / FAIL   Notes:

T41. Row events in the editor

Set up: Song mode, a song read from slot 1.

  1. Choose Row 2. Add on channel 5: type Program, choose a preset.
  2. Write song.

You should see: the event in the list with its channel, the device and the words. After the write, the read-back matches. not checked in simulator

Result: PASS / FAIL   Notes:

T42. Diagnostics

Set up: T37 done.

  1. Reset counters. Play a song for one minute. Read counters.

You should see: numbers for the control loop, longest flash erase and write, and key-to-MIDI. Lost ticks is the number to watch. A line "flash part (read by the SDK at boot): JEDEC 0x..., 1024 KiB; USER 471040 bytes". Write the JEDEC ID in Notes. not checked in simulator

Result: PASS / FAIL   Notes:

GROUP H. REAL GEAR

These tests need your gear. Use the Wrong Room rig channels from the MIDI guide, section 8, or your own. Cable the SMK-37 as in 3.1.

T43. An outside synth on its own channel

Set up: Proteus on channel 5 behind the H4MIDI (the H4MIDI sends channels 5 to 8 to the Proteus). Track 3 set to OUT CH 5, SEQ MIDI, OUT PORT ALL.

  1. On HOME turn K5 to track 3. The bottom line shows KEY T3 and the channel. Press a key. Or play a song with a part on track 3.

You should hear: the Proteus, not the SMK-37. Nothing from the other synths. not checked in simulator

Result: PASS / FAIL   Notes:

T44. A program change to an effects pedal

Set up: Zoom MS-70CDR+ on channel 16 (set USB MIDI CH 16, see the Help chapter 08 checklist). A song with a Program event in row 2 for channel 16.

  1. Send the song to the device. Press SEND SETUP if row 1 has events. Press PLAY.
  2. Jump to row 2 or let it arrive.

You should see: the pedal changes patch when row 2 starts, on the bar. If it changes late, the SONG page shows LATE. not checked in simulator

Result: PASS / FAIL   Notes:

T45. Two tracks to two devices through the H4MIDI

Set up: SMK-37 USB into the H4MIDI WC. Output 2 to the Proteus with channels 5 to 8. Another output to a second device, for example the M8 on channel 4. One part on track 3 (channel 5) and one on track 4 (channel 4).

  1. Play a song with both parts.

You should hear: each device plays only its own part. If a device plays the other part too, the H4MIDI filter is wrong. not checked in simulator

Result: PASS / FAIL   Notes:

T46. Clock out

Set up: M8 on its own DIN from the H4MIDI, set to follow MIDI clock. SEQ OUT ON. CLOCK on INT.

  1. Press PLAY on the SONG page.

You should see: the M8 starts with the SMK-37 and follows its tempo. Stop: it stops. not checked in simulator

Result: PASS / FAIL   Notes:

T47. Timing by ear

Set up: a song with the same hit on two devices, for example kick on the SMK-37 and a drum on the Proteus.

  1. Play it for one minute.

You should hear: the hits close together. A small drift of 10 to 14 ms between channels is the known limit (section 7). Write down anything you can hear as a flam or a stumble. not checked in simulator

Result: PASS / FAIL   Notes:

T48. No stuck notes

Set up: T43 or T45 playing.

  1. Press PLAY to stop in the middle of a long note.

You should hear: every note stops. MIDI Stop is sent once. not checked in simulator

Result: PASS / FAIL   Notes:

T49. A chord of more than four notes (tabby-v04.5)

Set up: a MIDI file with a chord of five or more notes on one track. Gear or a MIDI monitor on that track's channel.

  1. Import the file (5.2). The warnings list says the block is stored as a v3 clip. Nothing says "More than 4 notes ... kept the 4".
  2. Write the song to a slot. Select it on the SONG page and press PLAY.

You should hear: every note of the chord, together.

Result: PASS / FAIL   Notes:

T50. Controller events from the MIDI file (tabby-v04.5)

Set up: a MIDI file with a mod wheel or filter sweep (control changes) or pitch bend on a part. Gear that reacts to it.

  1. Import it with the box "keep controller, pitch bend and aftertouch events in the clips" ticked. The summary says how many were kept.
  2. Write the song and play it.

You should hear: the sweep or bend, in time with the notes. With the box unticked and the song written again, the notes play without it.

Result: PASS / FAIL   Notes:

T51. A row of 8 bars (tabby-v04.5)

Set up: a MIDI file of at least 8 bars of 4/4 with different notes in bars 5 to 8.

  1. Import it with Bars per row set to 8 bars (128 steps). Write it and play it.

You should hear: all 8 bars before the row repeats or the next row starts. The SONG page shows the row with 128 steps.

Result: PASS / FAIL   Notes:

T52. A song as scenes, and the master cycle (tabby-v04.6)

Set up: a MIDI file in 3/4 or 4/4 with a few bars. Gear or a MIDI monitor.

  1. Import it with the box "write the song as scenes and clips" ticked. The warnings list says how many scenes and clips, and the master cycle (16 steps for 4/4, 12 for 3/4).
  2. Write the song. On the SMK-37 select it on the SONG page and press PLAY: it plays as the file does.
  3. Press BT for the CLIPS page. Press a white pad, a little after a bar line.

You should hear: the launched clip start exactly on the next bar line of the song (the next multiple of the master cycle), not earlier. In a 3/4 song it starts on a 3/4 bar line.

Result: PASS / FAIL   Notes:

T53. Take a launch back, and the long press (tabby-v04.7)

Set up: T33 done, the song playing, the CLIPS page open.

  1. Press a white pad just after a bar line. While it blinks, press it again.
  2. Press and hold a white pad for a full second.

You should see: after step 1 TAKEN BACK, and nothing changes at the bar line. After step 2 SELECTED ONLY - TAKEN BACK; the pad is bright white and nothing changes at the bar line.

Result: PASS / FAIL   Notes:

T54. Mute from the pads (tabby-v04.7)

Set up: a song playing with a part on track 2 that goes to outside gear (or a MIDI monitor). The CLIPS page open.

  1. Hold SHIFT and press pad 10. Release SHIFT. Wait two bars.
  2. Hold SHIFT and press pad 10 again.

You should hear: after step 1 track 2 falls silent, on the SMK-37 and on the outside gear. After step 2 it is back, in time with the rest. With track 2 selected its pads are orange while it is muted, and the page says MUTED ALL.

Result: PASS / FAIL   Notes:

T55. Scene recall with pad lights (tabby-v04.7)

Set up: a song with at least two scenes, playing. The SONG page open (SCL from CLIPS).

  1. Press the pad of a scene that is not playing.

You should see: that pad blinks green, then turns green on the next bar line; the pad of the scene before goes dim white. Tracks you had launched or stopped follow the scene again.

Result: PASS / FAIL   Notes:

T56. BT from anywhere (tabby-v04.7)

Set up: any page, for example the mixer (MIX).

  1. Press BT. Press BT again.

You should see: the CLIPS page, then the page you were on.

Result: PASS / FAIL   Notes:

T57. Reserve a clip, then PLAY (tabby-v04.7.1)

Set up: the song stopped, the CLIPS page open, track 1 selected, a track with at least two clips.

  1. Press the pad of the clip that the song does not start with. It blinks. The screen says RESERVED - PLAY STARTS IT.
  2. Press PLAY.

You should hear: track 1 plays the reserved clip from the first beat and keeps looping it. The other tracks play the song as usual. ENV brings track 1 back to the song.

Result: PASS / FAIL   Notes:

T58. The two mutes look different (tabby-v04.7.1)

Set up: a song playing with a part on track 2 that goes to outside gear. The CLIPS page open, track 2 selected.

  1. Press MIX. On the mixer page mute track 2. Press MIX again to return.
  2. Unmute it on the mixer page the same way. Then hold SHIFT and press pad 10.

You should see and hear: after step 1 the pads of track 2 are blue and the page says MUTED INT; the SMK-37's own sound of track 2 is silent but the outside gear still plays. After step 2 the pads are orange, the page says MUTED ALL, and the outside gear is silent too. not checked in simulator

Result: PASS / FAIL   Notes:

T59. Enter and remove a note (tabby-v04.8)

Set up: a song on the device, stopped. CLIPS page, a clip selected (bright pad).

  1. Press EDIT. Press a pad that is off. Play a key.
  2. Play the same key again. Play it once more.

You should see: the STEP page; the pad cyan; after the key NOTE ENTERED, the note in the list, UNSAVED, the pad bright cyan. After the second press NOTE REMOVED, after the third it is back.

Result: PASS / FAIL   Notes:

T60. Hear the change while the clip loops (tabby-v04.8)

Set up: T59 done. Gear or the SMK-37's own sound on that track.

  1. Press EDIT (back to CLIPS). Press PLAY. Press the clip's pad so that it loops. Press EDIT again.
  2. Select another empty step and play a key.

You should hear: the new note in the loop from its next time round, on the step you chose. A white pad runs along the steps.

Result: PASS / FAIL   Notes:

T61. Velocity, start and length (tabby-v04.8)

Set up: T60 running, a step with one note selected.

  1. Turn K2 fully left, then right. Turn K3 a few clicks right. Turn K4 right.

You should hear: the note softer, then louder; then a little late; then longer. The screen shows VEL, ST+ and LEN change.

Result: PASS / FAIL   Notes:

T62. Undo and redo (tabby-v04.8)

Set up: T61 done.

  1. Press FX four times. Press FX once more. Hold SHIFT and press FX.

You should see: UNDO four times, each taking one change back; then NOTHING TO UNDO; then REDO.

Result: PASS / FAIL   Notes:

T63. Save, and saving by itself (tabby-v04.8)

Set up: an UNSAVED clip, the song playing.

  1. Press the 4th button in the left group.
  2. Press PLAY to stop. Wait ten seconds without touching anything.
  3. Switch the SMK-37 off and on. Play the song.

You should see: STOP TO SAVE while playing. After the stop, CLIP SAVED by itself and the page says SAVED. After the power cycle the song plays your changed clip.

Result: PASS / FAIL   Notes:

T64. Drums with the pads (tabby-v04.8)

Set up: the STEP page on a drum clip. Nothing selected.

  1. Play the key of the drum you want. Press SCL (PADS TOGGLE).
  2. Press pads 1, 5, 9 and 13. Press pad 5 again.

You should see and hear: the pads turn amber as the hits go on; pad 5 goes off again. Playing, the hits are on beats 1, 3 and 4.

Result: PASS / FAIL   Notes:

T65. Record from the keys (tabby-v04.9)

Set up: a song on the device, stopped. CLIPS page, a clip selected (bright pad).

  1. Press REC. Press PLAY.
  2. Play four notes in time with the music. Listen to the next time round.
  3. Press REC.

You should see and hear: REC ARMED - PLAY STARTS IT, then RECORDING and the REC lamp. Your notes come back in the loop, on the beat. REC STOPPED, and the lamp goes out. The STEP page shows the clip UNSAVED.

Result: PASS / FAIL   Notes:

T66. Your own timing (tabby-v04.9)

Set up: T65 done, the song playing, the clip looping.

  1. Hold SHIFT and press REC (INPUT QUANTIZE OFF). Press REC.
  2. Play a few notes deliberately late, between the beats. Press REC.

You should hear: the notes come back exactly as late as you played them.

Result: PASS / FAIL   Notes:

T67. Undo a take (tabby-v04.9)

Set up: T66 done.

  1. Press EDIT. Press FX. Hold SHIFT and press FX.

You should see and hear: UNDO, and the last take is gone from the loop at its next time round. REDO, and it is back.

Result: PASS / FAIL   Notes:

T68. Record from outside gear, with a controller (tabby-v04.9)

Set up: a keyboard or a DAW sends to the SMK-37 over USB on the channel of the selected track (SYNC / MIDI page, K1 IN CH). A clip looping, REC on.

  1. Play notes on the outside keyboard. Move its mod wheel slowly up and down once.
  2. Press REC. Listen.

You should hear: the notes and the wheel movement come back in the loop. On the STEP page EVENTS has grown by a few dozen for the wheel, not by hundreds. not checked in simulator

Result: PASS / FAIL   Notes:

T69. A new clip from an empty pad (tabby-v04.10)

Set up: a song loaded and stopped, CLIPS page, a track with an empty pad.

  1. Press the empty pad. Press REC. Press PLAY.
  2. Play a few notes over one bar. Press REC, then PLAY to stop. Wait ten seconds.

You should see and hear: the pad dim cyan after step 1; REC ARMED, then the take; your notes loop from the second bar; UNSAVED on the page, then SAVED. After switching the SMK-37 off and on, the pad still holds the clip. [checked in simulator]

Result: PASS / FAIL   Notes:

T70. A clip's length (tabby-v04.10)

Set up: a 1-bar clip selected on CLIPS and launched, the song playing.

  1. Press FX. On LENGTH turn K1 left 8 clicks: 8 STEPS.
  2. Listen for two bars. Turn K1 right 8 clicks.

You should hear: with 8 steps the first half of the clip twice a bar; back at 16 the second half is empty (NOTES PAST THE END REMOVED was shown). FX on the STEP page brings the notes back. [checked in simulator]

Result: PASS / FAIL   Notes:

T71. Copy a clip (tabby-v04.10)

Set up: the song stopped and saved, a clip selected on CLIPS.

  1. Press FX. Turn K5 to COPY TO PAD. The line shows an empty pad.
  2. Press the 4th button in the left group. Press FX.

You should see: COPIED - THE COPY IS OPEN; the pad you copied to holds a clip and is selected; UNSAVED until you save. Launch it: it plays the same notes. [checked in simulator]

Result: PASS / FAIL   Notes:

T72. The click as a MIDI note, and the count-in (tabby-v04.10)

Set up: a drum machine or a DAW on MIDI out, listening on channel 10. The song stopped.

  1. Press FX on CLIPS. Set COUNT-IN to 1 CYCLE, CLICK to ALWAYS, CLICK OUT to MIDI NOTE. Press FX.
  2. Select a clip. Press REC, then PLAY.

You should hear: four clicks (note 37 on channel 10), the first louder, then the song starts on the next beat and the click goes on with it. The screen shows COUNT-IN 4, 3, 2, 1. [checked in simulator]

Result: PASS / FAIL   Notes:

T73. The internal click (tabby-v04.10)

Set up: T72 done. Headphones or speakers on the SMK-37.

  1. Set CLICK OUT to INTERNAL. Press REC, then PLAY.
  2. Turn K8 down and up.

You should hear: the click from the SMK-37 itself, higher on the first beat of the bar; K8 changes its level with everything else. Set CLICK to OFF and COUNT-IN to OFF when you are done, and save. not checked in simulator

Result: PASS / FAIL   Notes:

T74. Store a scene (tabby-v04.10)

Set up: the song playing, a clip launched by hand on one track.

  1. Press SCL for SCENES. Press an empty pad short: HOLD TO STORE WHAT PLAYS AS A SCENE.
  2. Hold the same pad for half a second.
  3. Recall scene 1, then the new scene.

You should see and hear: STORED AS A NEW SCENE; the scene count goes up by one; recalling the new scene brings back the clips that played when you stored it. A pad that holds a scene only recalls it when held. [checked in simulator]

Result: PASS / FAIL   Notes:

T75. A clip chain (tabby-v04.11)

Set up: a track with two clips that sound different, the song stopped.

  1. Select the first clip, press FX. Set NEXT CLIP to the second clip and TIMES to 2. Press the 4th button in the left group (SAVED). Press FX.
  2. Select the second clip, press FX. Set NEXT CLIP to STOP. Save. Press FX.
  3. Press the first clip's pad, then PLAY.

You should hear: the first clip twice, then the second clip once, then the track is silent while the others play on. The CLIPS page shows +02 and later +STP under the track. [checked in simulator]

Result: PASS / FAIL   Notes:

T76. A fill-in with AFTER (tabby-v04.11)

Set up: T75 done. A third clip as a fill.

  1. On the fill clip set NEXT CLIP to the first clip and AFTER to 4 STEPS. Save.
  2. With the song playing, press the fill's pad.

You should hear: the fill starts on the next bar, plays 4 steps, and the first clip takes over from its beginning. not checked in simulator

Result: PASS / FAIL   Notes:

T77. The scene chain (tabby-v04.12)

Set up: a song with at least three scenes, stopped, SCENES page.

  1. Press pad 2: RESERVED - PLAY STARTS AT THIS SCENE. Turn K1 one click right. Press PLAY.
  2. Watch the SCENE number. When scene 3 plays, turn K3 right (CHAIN HELD). After a while turn it left.
  3. Press pad 1.

You should see and hear: the song starts at scene 2, which plays one time more than before; scene 3 follows by itself and repeats while the chain is held; pad 1 jumps to scene 1 and the song goes on from there. [checked in simulator]

Result: PASS / FAIL   Notes:

T78. A clip's program change (tabby-v04.13)

Set up: a synth on MIDI out that shows its program number, on the track's channel. The song stopped.

  1. Select a clip, press FX, set PROGRAM to 6. Save. Press FX.
  2. Press the clip's pad, then PLAY. Later launch another clip of the track, then this one again.

You should see: the synth goes to program 6 each time the track enters the clip, not on every loop. [checked in simulator]

Result: PASS / FAIL   Notes:

T79. Record a knob (tabby-v04.13)

Set up: a clip launched and looping, a synth on MIDI out that reacts to controller 74 (filter).

  1. Turn K1 on the CLIPS page. The screen shows K1 CONTROLLER 074 and a value; the synth's filter moves.
  2. Press REC. Turn K1 slowly down and up over one bar. Press REC.

You should hear: the filter movement comes back in every loop. On the STEP page EVENTS has grown by a dozen or so, not by hundreds. FX on the STEP page takes the take back. not checked in simulator

Result: PASS / FAIL   Notes:

T80. The click level (tabby-v04.14)

Set up: headphones or speakers on the SMK-37's audio output. A song loaded, stopped. CLICK on ALWAYS and CLICK OUT on INTERNAL (4.11).

  1. Press FX on CLIPS. Turn K5 to CLICK LEVEL on page 2/2. It says MID.
  2. Press PLAY. Turn K1 left to LOW, then right to HIGH.

You should hear: the click gets clearly quieter on LOW and louder on HIGH, without a crackle. HIGH is about as loud as a note you play. not checked in simulator

Result: PASS / FAIL   Notes:

T81. Choose a knob's controller (tabby-v04.14)

Set up: a synth or a MIDI monitor on MIDI out. A song loaded, stopped.

  1. Press FX on CLIPS. Turn K5 to K1 CONTROLLER. Turn K1 until it says 7. Press the 4th button in the left group: SAVED.
  2. Press FX. Turn K1.

You should see: the screen says K1 CONTROLLER 007 and a value, and the monitor shows controller 7 (volume on most gear). Load another song and come back: it is still 7. [checked in simulator]

Result: PASS / FAIL   Notes:

T82. A backup the page cannot read (tabby-v04.14)

Set up: only if you have a song saved by firmware newer than the page you open. Otherwise skip.

  1. Open the older page. In Projects & sounds click Full backup.

You should see: the backup line says STOPPED at song n: this page cannot read it, and what to do. No file is downloaded. [checked in simulator]

Result: PASS / FAIL   Notes:

T83. Transpose a clip (tabby-v04.15)

Set up: a clip with notes, launched and looping. A synth on MIDI out, or the track's own sound.

  1. Press FX on CLIPS. Turn K5 to TRANSPOSE. Turn K1 to +3.
  2. Listen for two loops. Turn K1 back to 0.

You should hear: from the next loop every note is three semitones higher; at 0 the clip sounds as before. The screen shows UNSAVED until you save. [checked in simulator]

Result: PASS / FAIL   Notes:

T84. Delete a clip (tabby-v04.15)

Set up: the song stopped. Make a copy of a clip first (COPY TO PAD), so nothing you need is lost.

  1. Select the copy, press FX, turn K5 to DELETE CLIP. Press the 4th button in the left group once.
  2. Wait three seconds. Press it once more. Then press it twice quickly.
  3. Select a clip that a scene plays and try the same.

You should see: one press, and presses three seconds apart, only ask (PRESS AGAIN TO DELETE THE CLIP). Two quick presses: CLIP DELETED - SAVE THE SONG and the pad goes dark. The scene's clip stays: USED BY SCENE n - NOT DELETED. [checked in simulator]

Result: PASS / FAIL   Notes:

7. KNOWN LIMITS AND WHAT IS NOT BUILT YET

Do not spend time testing these. They are known.

8. HOW TO REPORT A PROBLEM

Send these five lines.

  1. Test number: for example T30.
  2. What I did: the buttons I pressed in order.
  3. What happened: what I saw or heard.
  4. What the screen said: the exact words. Take a photo if you can.
  5. The version: from the boot screen, and the page version in the workbench.

If a write or an install failed, also say which page you used and what the page said. Do not try the install a second time before you report.